| ELECTRICAL ERROR ANGULAR RANGE IN MINUTES | -7.0 TO 7.0 |
| ACTUATOR FRICTION TORQUE AT PLUS 25 DEG CELSIUS | 0.10 INCH-OUNCES MAXIMUM |
| ALIGNMENT HOLE BOLT CIRCLE DIAMETER | 1.2500 INCHES NOMINAL |
| ALIGNMENT HOLE DEPTH | 0.1250 INCHES MINIMUM |
| ALIGNMENT HOLE QUANTITY | 4 |
| BODY MATERIAL | STEEL CORROSION RESISTING |
| BODY STYLE | STANDARD ROUND C |
| BODY SIZE | 18 |
| FLANGE DIAMETER | 1.7450 INCHES MINIMUM AND 1.7500 INCHES MAXIMUM |
| FLANGE THICKNESS | 0.0930 INCHES NOMINAL |
| FREQUENCY IN HERTZ | 60.0 NOMINAL |
| LENGTH | 0.1320 INCHES NOMINAL SHOULDER |
| OVERALL LENGTH | 3.1550 INCHES NOMINAL |
| MAXIMUM FUNDAMENTAL NULL VOLTAGE IN MILLIVOLTS PER VOLT | 60.00 OUTPUT |
| MAXIMUM TEMP RISE | 20.0 CELSIUS |
| MAXIMUM TOTAL NULL VOLTAGE OUTPUT IN MILLIVOLTS PER VOLT | 100.00 |
| MOUNTING SURFACE TO TERMINAL END DISTANCE | 2.6700 INCHES NOMINAL |
| SHOULDER DIAMETER | 1.5615 INCHES MINIMUM AND 1.5620 INCHES MAXIMUM |
| PILOT DIAMETER | 0.9370 INCHES MINIMUM AND 0.9375 INCHES MAXIMUM |
| PHASE SHIFT ANGLE IN DEG | 15.500 INPUT TO OUTPUT NOMINAL |
| PILOT LENGTH | 0.0400 INCHES NOMINAL |
| SHAFT DIAMETER | 0.1870 INCHES MINIMUM AND 0.1872 INCHES MAXIMUM SINGLE SHAFT |
| SHAFT NOMINAL THREAD SIZE | 0.190 INCHES SINGLE SHAFT |
| SHAFT THREAD CLASS | 2A SINGLE SHAFT |
| SHAFT THREAD DIRECTION | RIGHT-HAND SINGLE SHAFT |
| SHAFT THREAD LENGTH | 0.2000 INCHES NOMINAL SINGLE SHAFT |
| SHAFT THREAD SERIES DESIGNATOR | UNF SINGLE SHAFT |
| SHAFT TYPE | SPLINE W/THREADS SINGLE SHAFT |
| SHAFT LENGTH | 0.5400 INCHES NOMINAL SINGLE SHAFT |
| UNDERCUT DIAMETER | 1.6250 INCHES NOMINAL |
| UNDERCUT WIDTH | 0.0790 INCHES NOMINAL |
| ZRS IMPEDANCE ANGLE IN DEG | 12.00 MINIMUM AND 18.00 MAXIMUM |
| ZRS IMPEDANCE MAGNITUDE IN OHMS | 915.00 MINIMUM AND 1225.00 MAXIMUM |
| ZSO IMPEDANCE ANGLE IN DEG | 69.00 MINIMUM AND 75.00 MAXIMUM |
| ZSO IMPEDANCE MAGNITUDE IN OHMS | 1500.00 MINIMUM AND 1875.00 MAXIMUM |
| SPECIFICATION/STANDARD DATA | 81349-MIL-S-20708/36 GOVERNMENT SPECIFICATION |
| SPLINE TOOTH QUANTITY | 21 SINGLE SHAFT |
| SPLINE TOOTH DIAMETRAL PITCH | 120 SINGLE SHAFT |
| STATOR INPUT CURRENT RATING | 52.0 MILLIAMPERES MAXIMUM |
| STATOR INPUT ELECTRICAL POWER RATING | 1.1 WATTS NOMINAL |
| STATOR INPUT VOLTAGE RATING IN VOLTS | 90.0 NOMINAL |
| TERMINAL LOCATION | REAR |
| TERMINAL TYPE AND QUANTITY | 6 SCREW |
| TEST DATA DOCUMENT | 81349-MIL-S-20708 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| TRANSFORMATION RATIO | 1.154 ROTOR TO STATOR NOMINAL |