| ELECTRICAL ERROR ANGULAR RANGE IN MINUTES | -6.0 TO 6.0 |
| ALIGNMENT HOLE BOLT CIRCLE DIAMETER | 1.2500 INCHES NOMINAL |
| ALIGNMENT HOLE DEPTH | 0.1250 INCHES MINIMUM |
| ALIGNMENT HOLE QUANTITY | 4 |
| BODY SIZE | 18 |
| BODY STYLE | STANDARD ROUND C |
| CRITICALITY CODE JUSTIFICATION | FEAT |
| FLANGE DIAMETER | 1.7450 INCHES MINIMUM AND 1.7500 INCHES MAXIMUM |
| FLANGE THICKNESS | 0.0930 INCHES NOMINAL |
| FRAGILITY FACTOR | MODERATELY RUGGED |
| FREQUENCY IN HERTZ | 60.0 NOMINAL |
| LENGTH | 0.1320 INCHES NOMINAL SHOULDER |
| OVERALL LENGTH | 3.0600 INCHES NOMINAL |
| MATERIAL | STEEL CORROSION RESISTING BODY |
| MAXIMUM FUNDAMENTAL NULL VOLTAGE IN MILLIVOLTS PER VOLT | 50.00 OUTPUT |
| MAXIMUM TEMP RISE | 40.0 CELSIUS |
| MAXIMUM TOTAL NULL VOLTAGE OUTPUT IN MILLIVOLTS PER VOLT | 300.00 |
| MOUNTING SURFACE TO TERMINAL END DISTANCE | 2.5200 INCHES NOMINAL |
| PILOT DIAMETER | 0.9370 INCHES MINIMUM AND 0.9375 INCHES MAXIMUM |
| PILOT LENGTH | 0.0400 INCHES NOMINAL |
| PHASE SHIFT ANGLE IN DEG | 16.000 INPUT TO OUTPUT MAXIMUM |
| RECEIVER ERROR ANGULAR RANGE IN MINUTES | -45.0 TO 45.0 |
| ROTOR INPUT CURRENT RATING | 100.0 MILLIAMPERES MAXIMUM |
| ROTOR INPUT ELECTRICAL POWER RATING | 4.0 WATTS MAXIMUM |
| ROTOR INPUT VOLTAGE RATING IN VOLTS | 115.0 NOMINAL |
| SHAFT DIAMETER | 0.1870 INCHES MINIMUM AND 0.1872 INCHES MAXIMUM SINGLE SHAFT |
| SHAFT NOMINAL THREAD SIZE | 0.190 INCHES SINGLE SHAFT |
| SHAFT LENGTH | 0.5400 INCHES NOMINAL SINGLE SHAFT |
| SHAFT THREAD CLASS | 2A SINGLE SHAFT |
| SHAFT THREAD DIRECTION | RIGHT-HAND SINGLE SHAFT |
| SHAFT THREAD LENGTH | 0.2000 INCHES NOMINAL SINGLE SHAFT |
| SHAFT THREAD SERIES DESIGNATOR | UNF SINGLE SHAFT |
| SHAFT TYPE | SPLINE W/THREADS SINGLE SHAFT |
| SHOULDER DIAMETER | 1.5615 INCHES MINIMUM AND 1.5620 INCHES MAXIMUM |
| SPECIFICATION/STANDARD DATA | 81343-AS20708/35 PROFESSIONAL/INDUSTRIAL ASSOCIATION SPECIFICATION |
| SPECIAL FEATURES | STREAM (STD. TENSIONED REPLENISHMENT AT SEA METHOD) |
| ZSS IMPEDANCE ANGLE IN DEG | 18.00 MINIMUM AND 22.00 MAXIMUM |
| ZSS IMPEDANCE MAGNITUDE IN OHMS | 350.00 MINIMUM AND 430.00 MAXIMUM |
| SPLINE TOOTH DIAMETRAL PITCH | 120 SINGLE SHAFT |
| SPLINE TOOTH QUANTITY | 21 SINGLE SHAFT |
| TERMINAL LOCATION | REAR |
| TERMINAL TYPE AND QUANTITY | 5 SCREW |
| TEST DATA DOCUMENT | 81343-AS20708 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| TORQUE GRADIENT PER ANGULAR DEG | 0.050 INCH-OUNCES MINIMUM |
| TRANSFORMATION RATIO | 0.783 STATOR TO ROTOR NOMINAL |
| UNDERCUT DIAMETER | 1.6250 INCHES NOMINAL |
| UNDERCUT WIDTH | 0.0780 INCHES NOMINAL |