| ELECTRICAL ERROR ANGULAR RANGE IN MINUTES | -6.0 TO 6.0 |
| AFT OF FIRST FLANGE DIAMETER | 1.9985 INCHES MINIMUM AND 1.9995 INCHES MAXIMUM |
| BODY DIAMETER | 1.9900 INCHES MAXIMUM |
| BODY SIZE | 23 |
| BODY STYLE | STANDARD ROUND D |
| FLANGE DIAMETER | 2.2490 INCHES MINIMUM AND 2.2500 INCHES MAXIMUM |
| FLANGE THICKNESS | 0.2500 INCHES NOMINAL |
| FRAGILITY FACTOR | MODERATELY RUGGED |
| FREQUENCY IN HERTZ | 400.0 NOMINAL |
| LENGTH | 0.2500 INCHES NOMINAL SHOULDER |
| OVERALL LENGTH | 4.2990 INCHES NOMINAL |
| MATERIAL | STEEL CORROSION RESISTING BODY |
| MAXIMUM FUNDAMENTAL NULL VOLTAGE IN MILLIVOLTS PER VOLT | 30.00 OUTPUT |
| MAXIMUM TEMP RISE | 30.0 CELSIUS |
| MAXIMUM TOTAL NULL VOLTAGE OUTPUT IN MILLIVOLTS PER VOLT | 150.00 |
| MOUNTING SURFACE TO TERMINAL END DISTANCE | 3.5800 INCHES NOMINAL |
| PILOT DIAMETER | 0.5950 INCHES NOMINAL |
| PILOT LENGTH | 0.0430 INCHES NOMINAL |
| PHASE SHIFT ANGLE IN DEG | 2.000 INPUT TO OUTPUT NOMINAL |
| RECEIVER ERROR ANGULAR RANGE IN MINUTES | -45.0 TO 45.0 |
| ROTOR INPUT CURRENT RATING | 720.0 MILLIAMPERES MAXIMUM |
| ROTOR INPUT VOLTAGE RATING IN VOLTS | 115.0 NOMINAL |
| SECOND SHOULDER DIAMETER | 1.9985 INCHES MINIMUM AND 1.9995 INCHES MAXIMUM |
| SECOND SHOULDER LENGTH | 0.1700 INCHES NOMINAL |
| SHAFT DIAMETER | 0.2403 INCHES MINIMUM AND 0.2405 INCHES MAXIMUM SINGLE SHAFT |
| SHAFT NOMINAL THREAD SIZE | 0.250 INCHES SINGLE SHAFT |
| SHAFT LENGTH | 0.7190 INCHES NOMINAL SINGLE SHAFT |
| SHAFT THREAD CLASS | 2A SINGLE SHAFT |
| SHAFT THREAD DIRECTION | RIGHT-HAND SINGLE SHAFT |
| SHAFT THREAD LENGTH | 0.2900 INCHES NOMINAL SINGLE SHAFT |
| SHAFT THREAD SERIES DESIGNATOR | UNF SINGLE SHAFT |
| SHAFT TYPE | SPLINE W/THREADS SINGLE SHAFT |
| SHOULDER DIAMETER | 1.9850 INCHES MINIMUM AND 1.9900 INCHES MAXIMUM |
| SPECIFICATION/STANDARD DATA | 81349-MIL-S-20708/50 GOVERNMENT SPECIFICATION |
| ZSS IMPEDANCE ANGLE IN DEG | 42.00 MINIMUM AND 46.00 MAXIMUM |
| ZSS IMPEDANCE MAGNITUDE IN OHMS | 6.50 MINIMUM AND 8.10 MAXIMUM |
| SPLINE TOOTH DIAMETRAL PITCH | 96 SINGLE SHAFT |
| SPLINE TOOTH QUANTITY | 21 SINGLE SHAFT |
| TERMINAL LOCATION | REAR |
| TERMINAL TYPE AND QUANTITY | 5 SCREW |
| TEST DATA DOCUMENT | 81349-MIL-S-20708 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| TORQUE GRADIENT PER ANGULAR DEG | 0.250 INCH-OUNCES MINIMUM |
| TRANSFORMATION RATIO | 0.783 ROTOR TO STATOR NOMINAL |